Exfo FTB-8500 Series for FTB-500 Manual do Utilizador

User GuideFTB-8500 Series and FTB-8120NGE/8130NGE for FTB-500Ethernet andFibre Channel Application

Certification Informationx FTB-8500 Series and FTB-8120NGE/8130NGEFor continued compliance to the requirements of the EMC Directive: For FTB-8510G, u

Creating and Starting a Test Case86 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases2. For addi

Creating and Starting a Test CaseEthernet and Fibre Channel Application 87Ethernet RFC 2544 Test CaseEthernet RFC 2544 Test CaseRFC 2544: Allows Ether

Creating and Starting a Test Case88 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RFC 2544 Test CaseTo create an RFC 2544 test case:1. Test configur

Creating and Starting a Test CaseEthernet and Fibre Channel Application 89Ethernet RFC 2544 Test Case2. Port configuration:2a. Select the port Connect

Creating and Starting a Test Case90 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RFC 2544 Test Case3. Optical configuration for Ethernet 10G interf

Creating and Starting a Test CaseEthernet and Fibre Channel Application 91Ethernet RFC 2544 Test Case5. Traffic stream configuration5a. For IPv4, sele

Creating and Starting a Test Case92 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RFC 2544 Test Case6. For additional configuration parameters, refe

Creating and Starting a Test CaseEthernet and Fibre Channel Application 93Ethernet BERT Test CaseEthernet BERT Test CaseAllows Ethernet unframed and L

Creating and Starting a Test Case94 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet BERT Test CaseTo create a BERT test case:1. Test configuration:1a.

Creating and Starting a Test CaseEthernet and Fibre Channel Application 95Ethernet BERT Test Case2c. For Electrical RJ-45, if required, select the Eth

Certification InformationEthernet and Fibre Channel Application xiCE Declaration of Conformity Application of Council Directive(s): 2006/95/EC -

Creating and Starting a Test Case96 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet BERT Test Case4. Framing configuration:4a. Select the test framing

Creating and Starting a Test CaseEthernet and Fibre Channel Application 97Ethernet BERT Test Case4b. For Ethernet Unframed, select the Enable Sync che

Creating and Starting a Test Case98 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet BERT Test Case5. Traffic stream configuration:Only Frame Size and

Creating and Starting a Test CaseEthernet and Fibre Channel Application 99Ethernet BERT Test Case5g. Enter the Maximum Rate (%), the default setting i

Creating and Starting a Test Case100 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test CaseEthernet Frame Analyzer Test CaseAllows E

Creating and Starting a Test CaseEthernet and Fibre Channel Application 101Ethernet Frame Analyzer Test CaseTo create a Frame Analyzer test case:1. Te

Creating and Starting a Test Case102 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test Case2. Port configuration:2a. Select the port

Creating and Starting a Test CaseEthernet and Fibre Channel Application 103Ethernet Frame Analyzer Test Case3. Optical configuration for Ethernet 10G

Creating and Starting a Test Case104 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test Case4c. Select the PBB-TE check box to enable

Creating and Starting a Test CaseEthernet and Fibre Channel Application 105Ethernet Frame Analyzer Test Case5. Traffic stream configuration:5a. Select

Certification Informationxii FTB-8500 Series and FTB-8120NGE/8130NGE Application of Council Directive(s): 2006/95/EC - The Low Voltage Directive

Creating and Starting a Test Case106 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test Case5f. Set the VLAN parameters when required

Creating and Starting a Test CaseEthernet and Fibre Channel Application 107Ethernet Smart Loopback Test CaseEthernet Smart Loopback Test CaseAllows tr

Creating and Starting a Test Case108 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Smart Loopback Test Case1f. For FTB-8510B, select the port number

Creating and Starting a Test CaseEthernet and Fibre Channel Application 109Ethernet Smart Loopback Test Case2. Optical configuration for Ethernet 10G

Creating and Starting a Test Case110 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Smart Loopback Test Case3. Framing configuration:3a. Set the Auto

Creating and Starting a Test CaseEthernet and Fibre Channel Application 111Ethernet TCP Throughput Test CaseEthernet TCP Throughput Test CaseTCP Throu

Creating and Starting a Test Case112 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet TCP Throughput Test Case2. Port configuration:Port 1 (FTB-8510B o

Creating and Starting a Test CaseEthernet and Fibre Channel Application 113Ethernet TCP Throughput Test Case4. Press the TCP Throughput tab and TCP Th

Creating and Starting a Test Case114 FTB-8500 Series and FTB-8120NGE/8130NGEFibre Channel BERT Test CaseFibre Channel BERT Test CaseTypical Fibre Chan

Creating and Starting a Test CaseEthernet and Fibre Channel Application 115Fibre Channel BERT Test Case2. Port configuration:2a. For FTB-8510B, select

Certification InformationEthernet and Fibre Channel Application xiii Application of Council Directive(s): 2006/95/EC - The Low Voltage Directive

Creating and Starting a Test Case116 FTB-8500 Series and FTB-8120NGE/8130NGEFibre Channel BERT Test Case3. Framing selection:3a. Select the test frami

Creating and Starting a Test CaseEthernet and Fibre Channel Application 117Fibre Channel BERT Test Case4. Framing configuration (available with FC Fra

Ethernet and Fibre Channel Application 1197 Summary TabsThe summary tabs allow to configure the test parameters and to view the test status and result

Summary Tabs120 FTB-8500 Series and FTB-8120NGE/8130NGETest Summar yTest Status Start Time: Indicates the date and time the test has been started. Th

Summary TabsEthernet and Fibre Channel Application 121Test Summar y SAM Test Status: Indicates the EtherSAM test status message.Test Status Desciptio

Summary Tabs122 FTB-8500 Series and FTB-8120NGE/8130NGETest Summar y RFC 2544: Indicates the status of the running RFC 2544 test. This setting is onl

Summary TabsEthernet and Fibre Channel Application 123Test Summar yClock Configuration Clock Mode indicates the clock mode selected during the test s

Summary Tabs124 FTB-8500 Series and FTB-8120NGE/8130NGETest Summar yTimer ConfigurationAllows to automatically start and/or stop a test case at a give

Summary TabsEthernet and Fibre Channel Application 125Test Summar y On/Off button allows enabling the test timer. An error message is displayed and t

Summary Tabs126 FTB-8500 Series and FTB-8120NGE/8130NGEAlarm SummaryAlarm SummaryPress TEST, Summary, and Alarm.The Alarm summary tab gives access to

Summary TabsEthernet and Fibre Channel Application 127Alarm Summary TestGlobal: Indicates the presence of any alarms/errors related to the test such

Summary Tabs128 FTB-8500 Series and FTB-8120NGE/8130NGEAlarm Summary Higher Layer Protocol (Ethernet): Indicates the presence of any error related to

Summary TabsEthernet and Fibre Channel Application 129Test LoggerTest LoggerPress TEST, Summary, and Alarm.The Test Logger lists the test status/event

Summary Tabs130 FTB-8500 Series and FTB-8120NGE/8130NGETest LoggerLogger TableAn event is automatically listed in the logger and saved on the hard dri

Ethernet and Fibre Channel Application 1318Port TabsThe port tabs allow to configure different port parameters and to view the port analysis.Note: The

Port Tabs132 FTB-8500 Series and FTB-8120NGE/8130NGEElectrical TXElectrical TXPress TEST, Port, and Electrical TX.ConfigurationEthernet port crossover

Port TabsEthernet and Fibre Channel Application 133Electrical TXFrequencyNote: Frequency offset generation is only available on the FTB-8510B. However

Port Tabs134 FTB-8500 Series and FTB-8120NGE/8130NGEElectrical RXElectrical RXPress TEST, Port, and Electrical RX.Alarm AnalysisFrequency: The frequen

Port TabsEthernet and Fibre Channel Application 135Electrical RXFrequency AnalysisNote: Frequency Analysis is not available for 10Base-T test. Freque

Ethernet and Fibre Channel Application 11 Introducing the Ethernet and Fibre Channel ApplicationFully integrated test solution for performance assessm

Port Tabs136 FTB-8500 Series and FTB-8120NGE/8130NGEOptical TXOptical TXPress TEST, Port, and Optical TX.Signal Analysis Output Presence: Indicates t

Port TabsEthernet and Fibre Channel Application 137Optical TXFrequencyNote: Frequency offset is not available when Through Mode (FTB-8510B only) is se

Port Tabs138 FTB-8500 Series and FTB-8120NGE/8130NGEOptical RXOptical RXPress TEST, Port, and Optical RX.Signal Analysis Power Level (dBm): Indicates

Port TabsEthernet and Fibre Channel Application 139Optical RXFrequency AnalysisFrequency (bps): Indicates the frequency of the input signal in bps.Fre

Port Tabs140 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Ethernet)Interface Setup (Ethernet)Note: For Fibre Channel test case, see Interfa

Port TabsEthernet and Fibre Channel Application 141Interface Setup (Ethernet) Enable Auto-Negotiation (Not available on FTB-8510G)The Auto-Negotiatio

Port Tabs142 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Ethernet) Flow ControlAvailable with Frame Analyzer (FTB-8510B and FTB-8510G), R

Port TabsEthernet and Fibre Channel Application 143Interface Setup (Ethernet)Status Link: A green Link LED indicates that there is a link at the inpu

Port Tabs144 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Fibre Channel)Interface Setup (Fibre Channel)Note: For Ethernet test case, see In

Port TabsEthernet and Fibre Channel Application 145Interface Setup (Fibre Channel)LoginThe capability to log in is available only if a successful link

Introducing the Ethernet and Fibre Channel Application2 FTB-8500 Series and FTB-8120NGE/8130NGE Capability to perform full-line-rate data capture and

Port Tabs146 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Fibre Channel) Port Status: Indicates the status of the port login process. Poss

Port TabsEthernet and Fibre Channel Application 147Interface Setup (Fibre Channel)Buffer-to-Buffer Flow Control Enable: The Enable check box is force

Port Tabs148 FTB-8500 Series and FTB-8120NGE/8130NGENetworkNetworkNote: Network is only available with Framed Layer 2 and when Through Mode (FTB-8510B

Port TabsEthernet and Fibre Channel Application 149NetworkSource MAC ConfigurationMAC Address: A default and unique Media Access Control (MAC) address

Port Tabs150 FTB-8500 Series and FTB-8120NGE/8130NGENetworkSource IP ConfigurationFor IPv4: Automatic IP Address: Allows to dynamically obtain an IP

Port TabsEthernet and Fibre Channel Application 151NetworkFor IPv6: Displays the Link-Local IPv6 Address, Global IPv6 Address, and Default Gateway Ad

Port Tabs152 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. TXAdvanced Auto-Neg. TXNote: Advanced auto-negotiation is not available with th

Port TabsEthernet and Fibre Channel Application 153Advanced Auto-Neg. TXConfigurationThe Speed, Duplex, and Flow Control can be modified only when the

Port Tabs154 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. TXNote: Only None is available for BERT analyzer test.Note: Flow Control should

Port TabsEthernet and Fibre Channel Application 155Advanced Auto-Neg. TXAuto-Neg. Fault Register Fault Type: Allows the generation of a fault during

Introducing the Ethernet and Fibre Channel ApplicationEthernet and Fibre Channel Application 3ConventionsConventionsBefore using the product described

Port Tabs156 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. TXNegotiate ButtonThe Negotiate button allows starting the auto-negotiation pro

Port TabsEthernet and Fibre Channel Application 157Advanced Auto-Neg. RXAdvanced Auto-Neg. RXNote: Advanced auto-negotiation is not available with the

Port Tabs158 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. RX Duplex: Indicates the negotiated duplex mode. Possible values are Half, and

Ethernet and Fibre Channel Application 1599 Traffic Analyzer TabsNote: The available Traffic Analyzer tabs depend on which test path is activated.Test

Traffic Analyzer Tabs160 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet TXEthernet TXNote: Available with BERT test with Framed Layer 1 and Framed La

Traffic Analyzer TabsEthernet and Fibre Channel Application 161Ethernet TXPHY Error Injection Type: The following error is available with both manual

Traffic Analyzer Tabs162 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet TX Rate: Press the Rate field to select the rate for the automated error. Ch

Traffic Analyzer TabsEthernet and Fibre Channel Application 163Ethernet RXEthernet RXPress TEST, Traffic Analyzer, and Eth. RX.ConfigurationOversize M

Traffic Analyzer Tabs164 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RXErrors Analysis Block (10Gig-E): The number of frames received with an err

Traffic Analyzer TabsEthernet and Fibre Channel Application 165Ethernet RXThe following errors are only available with Half Duplex mode. Not available

Traffic Analyzer Tabs166 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet StatisticsEthernet StatisticsPress TEST, Traffic Analyzer, and Eth. Stats.Val

Traffic Analyzer TabsEthernet and Fibre Channel Application 167Ethernet StatisticsFrame Size Count: Gives the count of each received frame size (vali

Traffic Analyzer Tabs168 FTB-8500 Series and FTB-8120NGE/8130NGEPBB-TEPBB-TEAnalyzes streams with PBB-TE data traffic.Note: The PBB-TE check box has b

Traffic Analyzer TabsEthernet and Fibre Channel Application 169PBB-TEPPB-TE Frame Size Count: Gives the count of each received PBB-TE frame size (val

Traffic Analyzer Tabs170 FTB-8500 Series and FTB-8120NGE/8130NGEHigher LayersHigher LayersPress TEST, Traffic Analyzer, and Higher Layers.Higher Layer

Traffic Analyzer TabsEthernet and Fibre Channel Application 171Higher LayersMPLSNote: MPLS is only availabe when enabled from the test setup.Frame Cou

Traffic Analyzer Tabs172 FTB-8500 Series and FTB-8120NGE/8130NGEFlow ControlFlow ControlPress TEST, Traffic Analyzer, and Flow Control.Note: One Quant

Traffic Analyzer TabsEthernet and Fibre Channel Application 173Flow ControlNote: When entering a value in μs/ns it will be rounded to the closest mult

Traffic Analyzer Tabs174 FTB-8500 Series and FTB-8120NGE/8130NGEFlow ControlStatistics Pause Time: Indicates the total number of pause time received

Traffic Analyzer TabsEthernet and Fibre Channel Application 175Traffic FiltersTraffic FiltersAllows gathering statistics according to the programmed f

Ethernet and Fibre Channel Application 52 Safety InformationLaser Safety WarningsWARNINGWhen the LASER LED is on, the FTB-8500 Series and FTB-8120NGE/

Traffic Analyzer Tabs176 FTB-8500 Series and FTB-8120NGE/8130NGETraffic FiltersFilter ConfigurationAllows to configure the criteria for the selected f

Traffic Analyzer TabsEthernet and Fibre Channel Application 177Traffic FiltersIPv6aIPv6 Destination AddressIPv6 Source AddressIPv6 Flow LabelIPv6 Next

Traffic Analyzer Tabs178 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Filters ValueAllows entering the value associated to the selected filter. See

Traffic Analyzer TabsEthernet and Fibre Channel Application 179Traffic FiltersFrame CountIndicates the number of frame matching the configured filter’

Traffic Analyzer Tabs180 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Filter ConfigurationTraffic Filter ConfigurationAllows gathering statistics ac

Traffic Analyzer TabsEthernet and Fibre Channel Application 181Traffic Filter ConfigurationFilter: Allows the selection of the filter to be used. The

Traffic Analyzer Tabs182 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Filter StatsTraffic Filter StatsAllows gathering statistics according to the p

Traffic Analyzer TabsEthernet and Fibre Channel Application 183Traffic Filter StatsThroughputIndicates throughput statistics of frame matching the con

Traffic Analyzer Tabs184 FTB-8500 Series and FTB-8120NGE/8130NGECaptureCaptureCapture is a troubleshooting tool used to capture received data traffic

Traffic Analyzer TabsEthernet and Fibre Channel Application 185Capture Frame LengthAllows to select the length of the frame that will be saved in the

ii FTB-8500 Series and FTB-8120NGE/8130NGECopyright © 2003–2012 EXFO Inc. All rights reserved. No part of this publication may be reproduced, stored i

Safety Information6 FTB-8500 Series and FTB-8120NGE/8130NGEInstallation Instruction WarningsInstallation Instruction WarningsWARNINGUse of optical ins

Traffic Analyzer Tabs186 FTB-8500 Series and FTB-8120NGE/8130NGECaptureTrigger Trigger Type: Allows to define the trigger source criterion that will

Traffic Analyzer TabsEthernet and Fibre Channel Application 187Capture Trigger Position: Allows the selection of the triggered frame position within

Traffic Analyzer Tabs188 FTB-8500 Series and FTB-8120NGE/8130NGECapture Capture button: Allows to start/stop the data capture. The test must be runni

Traffic Analyzer TabsEthernet and Fibre Channel Application 189GraphGraphGives the graph showing the test measurement results.Press TEST, Traffic Anal

Traffic Analyzer Tabs190 FTB-8500 Series and FTB-8120NGE/8130NGEFC TXFC TXPress TEST, Traffic Analyzer, and FC TX.Alarm Generation Type: The followin

Traffic Analyzer TabsEthernet and Fibre Channel Application 191FC TXPHY Error Injection Type: The following errors are available with both manual and

Traffic Analyzer Tabs192 FTB-8500 Series and FTB-8120NGE/8130NGEFC TXFC Error InjectionNote: FC Error Injection is available with Framed Layer 2 only.

Traffic Analyzer TabsEthernet and Fibre Channel Application 193FC RXFC RXPress TEST, Traffic Analyzer, and FC RX.Alarm Analysis Link Down: Indicates

Traffic Analyzer Tabs194 FTB-8500 Series and FTB-8120NGE/8130NGEFC RXError Analysis Block (FC 10x): The number of frames received with an errored blo

Traffic Analyzer TabsEthernet and Fibre Channel Application 195FC LatencyFC LatencyNote: Available with FC Framed Layer 1 and FC Framed Layer 2 only.P

Safety InformationEthernet and Fibre Channel Application 7Installation Instruction WarningsCAUTIONElectrostatic Discharge (ESD) Sensitive Equipment:Pl

Traffic Analyzer Tabs196 FTB-8500 Series and FTB-8120NGE/8130NGEFC LatencyLatency MeasurementsRound Trip Delay  Maximum: Indicates the maximum time t

Traffic Analyzer TabsEthernet and Fibre Channel Application 197FC StatisticsFC StatisticsNote: Available with FC Framed Layer 1 and FC Framed Layer 2

Ethernet and Fibre Channel Application 19910 Stream Generation TabsNote: Stream generation is not available with Smart Loopback and TCP Throughput (FT

Stream Generation Tabs200 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewOverviewThe Overview tab allows configuration and activation of up to 10 stre

Stream Generation TabsEthernet and Fibre Channel Application 201Overview Enable: Allows enabling the corresponding stream. However, the stream will b

Stream Generation Tabs202 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Copy Stream buttonTo copy the stream configuration to one or several stream

Stream Generation TabsEthernet and Fibre Channel Application 203OverviewFor BERT and RFC 2544 tests on FTB-8510B and FTB-8510G No: Indicates the stre

Stream Generation Tabs204 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewFor BERT and RFC 2544 tests on FTB-8120NGE, FTB-8130NGE, FTB-8525, and FTB-85

Stream Generation TabsEthernet and Fibre Channel Application 205Overview Data Link: Select the data link type (layer 2). Choices are Ethernet II and

Stream Generation Tabs206 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewThe following table lists each component that may affect the minimum size val

Stream Generation TabsEthernet and Fibre Channel Application 207Stream ConfigurationStream ConfigurationPress TEST, Stream Gen, and Stream Config.Stre

Stream Generation Tabs208 FTB-8500 Series and FTB-8120NGE/8130NGEStream ConfigurationFor Video: Video Codec: Choices are SDTV (MPEG-2), HDTV (MPEG-2)

Stream Generation TabsEthernet and Fibre Channel Application 209Stream Configuration Transport: Select the transport traffic type (layer 4). Choices

Stream Generation Tabs210 FTB-8500 Series and FTB-8120NGE/8130NGEStream ConfigurationThe following table lists each component that may affect the mini

Stream Generation TabsEthernet and Fibre Channel Application 211Stream Configuration For BERT test:For Framed Layer 1, only the Data Link (Ethernet)

Stream Generation Tabs212 FTB-8500 Series and FTB-8120NGE/8130NGEStream ConfigurationThe following table lists each component that may affect the mini

Stream Generation TabsEthernet and Fibre Channel Application 213Stream ConfigurationTraffic Shaping Transmit Mode: Allows the selection of the Transm

Stream Generation Tabs214 FTB-8500 Series and FTB-8120NGE/8130NGEStream Configuration TX Rate: Enter the transmission rate. The available stream tran

Stream Generation TabsEthernet and Fibre Channel Application 215Stream ConfigurationFor Ramp Traffic ShapingNote: Available for Stream 1 with Ramp and

Ethernet and Fibre Channel Application 93 Getting StartedIf the Ethernet and Fibre Channel Application has been purchased at the same time as the FTB-

Stream Generation Tabs216 FTB-8500 Series and FTB-8120NGE/8130NGEPBB-TEPBB-TEAllows configuration of PBB-TE streams including B-MAC (source and destin

Stream Generation TabsEthernet and Fibre Channel Application 217PBB-TEDestination B-MAC Address: Enter the destination Backbone MAC address for the s

Stream Generation Tabs218 FTB-8500 Series and FTB-8120NGE/8130NGEMACMACNote: Only available with Framed Layer 2.Press TEST, Stream Gen, and MAC.Stream

Stream Generation TabsEthernet and Fibre Channel Application 219MACSourceMAC Address: Indicates the MAC address of the selected stream.Note: The sourc

Stream Generation Tabs220 FTB-8500 Series and FTB-8120NGE/8130NGEMACVLANNote: For RFC 2544 test, VLAN is only configurable through the Network on page

Stream Generation TabsEthernet and Fibre Channel Application 221MPLSMPLSAllows MPLS configuration of streams with up to two layers of MPLS labels, COS

Stream Generation Tabs222 FTB-8500 Series and FTB-8120NGE/8130NGEMPLSMPLS Configuration Stacked Headers: Allows the activation of up to two MPLS head

Stream Generation TabsEthernet and Fibre Channel Application 223IP/UDP/TCPIP/UDP/TCPNote: Only available when the network stream configuration is set

Stream Generation Tabs224 FTB-8500 Series and FTB-8120NGE/8130NGEIP/UDP/TCPFor IPv6:Displays the Link-Local IPv6 Address, Global IPv6 Address, and Def

Stream Generation TabsEthernet and Fibre Channel Application 225IP/UDP/TCP IP TOS/DS for IPv4 or Traffic Class (TOS/DS) for IPv6Enter the user define

Stream Generation Tabs226 FTB-8500 Series and FTB-8120NGE/8130NGEPayloadPayloadNote: For FTB-8510B and FTB-8510G, not available with BERT test. For FT

Stream Generation TabsEthernet and Fibre Channel Application 227Frame Configuration (Fibre Channel)Frame Configuration (Fibre Channel)Note: Frame Conf

Stream Generation Tabs228 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel) EOF: The EOF represents the End Of Frame delimit

Stream Generation TabsEthernet and Fibre Channel Application 229Frame Configuration (Fibre Channel)Frame Parameter Size: Allows the selection of the

Stream Generation Tabs230 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel)FC HeaderNote: FC Header is only available with Fi

Stream Generation TabsEthernet and Fibre Channel Application 231Frame Configuration (Fibre Channel) D_ID: The Destination Identifier specifies the lo

Stream Generation Tabs232 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel) CS_CTL: The Class Specific Control field contain

Stream Generation TabsEthernet and Fibre Channel Application 233Frame Configuration (Fibre Channel) F_CTL: The Frame Control contains control informa

Stream Generation Tabs234 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel)9Retransmitted Sequence0 = Original Sequence trans

Stream Generation TabsEthernet and Fibre Channel Application 235Frame Configuration (Fibre Channel) SEQ_ID: The Sequence Identifier specifies the seq

Ethernet and Fibre Channel Application 114 Physical Interfaces and LEDsThis section describes all FTB-8500 Series and FTB-8120NGE/8130NGE models, conn

Ethernet and Fibre Channel Application 23711 Stream Analyzer TabsNote: Stream analyzer is only available with Frame Analyzer test. Stream analyzer tab

Stream Analyzer Tabs238 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Latency Cur. (ms) indicates for each stream the current measured round trip l

Stream Analyzer TabsEthernet and Fibre Channel Application 239StreamStreamPress TEST, Stream Analyzer, and Stream.Note: Available with Frame Analyzer

Stream Analyzer Tabs240 FTB-8500 Series and FTB-8120NGE/8130NGEStreamThroughputThe throughput is measured for each stream on all valid frames (valid T

Ethernet and Fibre Channel Application 24112 WIS TabsNote: The WIS tabs are only available with 10 GigE WAN transceiver mode. Not available with Smart

WIS Tabs242 FTB-8500 Series and FTB-8120NGE/8130NGEWIS TXAlarm GenerationNote: Alarm generation is available with BERT test only. Type: The following

WIS TabsEthernet and Fibre Channel Application 243WIS TX ERDI-PCD (Enhanced RDI - Path Connectivity Defect): Generates a “110” pattern for bits 5, 6

WIS Tabs244 FTB-8500 Series and FTB-8120NGE/8130NGEWIS TXPath Signal Label (C2)The C2 byte is allocated to indicate the content of the STS SPE, includ

WIS TabsEthernet and Fibre Channel Application 245WIS RXWIS RXPress TEST, WIS, and WIS RX.Error Analysis B1 (BIP-8, Bit-Interleave Parity - 8 bits):

Physical Interfaces and LEDs12 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8510B ModelElectrical 10/100/1000 Mbps EthernetThe FTB-8510B module provides

WIS Tabs246 FTB-8500 Series and FTB-8120NGE/8130NGEWIS RX REI-L (Remote Error Indicator - Line): The REI-L error is declared when bits 5 through 8 of

WIS TabsEthernet and Fibre Channel Application 247WIS RX LOP-P (Loss Of Pointer - Path): For non-concatenated payloads, the LOP-P alarm indicates tha

WIS Tabs248 FTB-8500 Series and FTB-8120NGE/8130NGEWIS OH RXWIS OH RXAllows verification of the transport overhead information received.Press TEST, WI

WIS TabsEthernet and Fibre Channel Application 249WIS OH RXSection OverheadNote: Monitor the first timeslot only. A1 and A2: Framing. The value shoul

WIS Tabs250 FTB-8500 Series and FTB-8120NGE/8130NGEWIS OH RXPath Overhead J11: Trace. B31: BIP-8 C2: Signal Label G1: Status F2: User Channel H4

Ethernet and Fibre Channel Application 25113 Pattern TabsNote: The Pattern tabs are only available with BERT test.TabAvailable withPageEthernet Fibre

Pattern Tabs252 FTB-8500 Series and FTB-8120NGE/8130NGEPattern TXPattern TXPress TEST, and Pattern.Configuration Test Pattern: Select the test patter

Pattern TabsEthernet and Fibre Channel Application 253Pattern TX Invert: The generated test pattern will be inverted if the Invert check box is selec

Pattern Tabs254 FTB-8500 Series and FTB-8120NGE/8130NGEPattern TXError InjectionAllows selection and configuration of a manual or automated pattern er

Pattern TabsEthernet and Fibre Channel Application 255Pattern RXPattern RXPress TEST, and Pattern.ConfigurationNote: See Configuration on page 252 for

Physical Interfaces and LEDsEthernet and Fibre Channel Application 13FTB-8510B ModelOptical 100/1000 Mbps Ethernet or1x/2x Fibre ChannelThe FTB-8510B-

Pattern Tabs256 FTB-8500 Series and FTB-8120NGE/8130NGEPattern RXError AnalysisBit Error: A Bit Error indicates that there are logic errors in the bit

Ethernet and Fibre Channel Application 25714 IPTV TabsNote: The IPTV tabs are available with Frame Analyzer application type on the FTB-8510B module o

IPTV Tabs258 FTB-8500 Series and FTB-8120NGE/8130NGEIPTV Testing with the FTB-8510BIPTV Testing with the FTB-8510BThe FTB-8510B module provides the ca

IPTV TabsEthernet and Fibre Channel Application 259IPTV Testing with the FTB-8510BThe FTB-8510B module equipped with the IPTV option can be used at di

IPTV Tabs260 FTB-8500 Series and FTB-8120NGE/8130NGEDiscoveryDiscoveryThe Discovery page allows the auto-discovery function to automatically scans the

IPTV TabsEthernet and Fibre Channel Application 261DiscoveryThe status of each stream, active or inactive, is visually presented as follow: Active: S

IPTV Tabs262 FTB-8500 Series and FTB-8120NGE/8130NGEDiscoveryStream MonitoringThe Add function adds the streams to the stream monitoring list in the o

IPTV TabsEthernet and Fibre Channel Application 263DiscoverySelection OptionsNote: Selection Options is not available when Auto-Add is selected. Only

IPTV Tabs264 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewOverviewThe Overview tab provides a summary of the key statistics that can be used as firs

IPTV TabsEthernet and Fibre Channel Application 265OverviewTo organize the streams key statistics presentation, the Overview page supports several sor

Physical Interfaces and LEDs14 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8510B Model LEDs for Optical PortsLED Status DescriptionLASER(Red)On An opt

IPTV Tabs266 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewColumn Description Join Status: Indicates the join status for each multicast stream only.

IPTV TabsEthernet and Fibre Channel Application 267Overview DF (ms): The Delay Factor (DF) provides a measure of the maximum packet delay variation o

IPTV Tabs268 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewStream StatusThe status of each stream, active or inactive, is visually presented as follo

IPTV TabsEthernet and Fibre Channel Application 269OverviewAdd ButtonThe Add button adds streams to the stream monitoring list. The Add button is disa

IPTV Tabs270 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Deselect All deselects all the streams in the list.Manual Entry, when selected, adds one

IPTV TabsEthernet and Fibre Channel Application 271OverviewDelete ButtonThe Delete button removes streams from the stream monitoring list. Streams can

IPTV Tabs272 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewManual Entry, when selected, removes one specific stream. Destination IP Address: Enter t

IPTV TabsEthernet and Fibre Channel Application 273OverviewIGMP ButtonThe IGMP button facilitates the management of the IGMP capabilities associated t

IPTV Tabs274 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewStreams can be sorted using Stream Name, Dest IP address, Auto Join, or Join Status. When

IPTV TabsEthernet and Fibre Channel Application 275Overview Disable Auto-Join / Leave Button: This button toggles from Disable Auto-Join to Leave whe

Physical Interfaces and LEDsEthernet and Fibre Channel Application 15FTB-8510G ModelFTB-8510G ModelFTB-8510G-LAN: One 10 Gigabit Ethernet LAN PHY (10.

IPTV Tabs276 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Join Status: The Join-Status is represented by the following icons. Icons become grayed

IPTV TabsEthernet and Fibre Channel Application 277OverviewAlias MapAllows the creation of a table establishing the relation between a destination IP

IPTV Tabs278 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Alias Add allows a new alias map entry to the IPTV alias map list. Use the Stream Name

IPTV TabsEthernet and Fibre Channel Application 279MDI/TR 101 290MDI/TR 101 290The MDI/TR 101 290 page contains the detailed statistics associated to

IPTV Tabs280 FTB-8500 Series and FTB-8120NGE/8130NGEMDI/TR 101 290StreamThe Select Stream pop up allows the selection of a stream to see its statistic

IPTV TabsEthernet and Fibre Channel Application 281MDI/TR 101 290MDI (Media Delivery Index)The use of the Media Delivery Index as a testing metric pro

IPTV Tabs282 FTB-8500 Series and FTB-8120NGE/8130NGEMDI/TR 101 290Note: The Delay Factor (and associated Virtual Buffer Size) value behavior can chang

IPTV TabsEthernet and Fibre Channel Application 283MDI/TR 101 290TR 101 290The TR 101 290 determines the integrity of the MPEG-2 Transport Stream acro

IPTV Tabs284 FTB-8500 Series and FTB-8120NGE/8130NGEMDI/TR 101 290PMT Error2: Indicates that any of the following conditions appear during a 1 second

IPTV TabsEthernet and Fibre Channel Application 285MDI/TR 101 290TR 101 290 ThresholdTR 101 290 Threshold parameters apply to all streams. PCR Jitter

Ethernet and Fibre Channel Application iiiContentsCertification Information ...

Physical Interfaces and LEDs16 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8510G ModelCarefully connect optical fiber cables to the XFP’s IN and OUT po

IPTV Tabs286 FTB-8500 Series and FTB-8120NGE/8130NGEIGMPIGMPThe IGMP functions associated to all streams currently support Version 2 of the IGMP stand

IPTV TabsEthernet and Fibre Channel Application 287IGMPTo access the IGMP tab, press TEST, IPTV, and IGMP.Multicast GroupStreamThe Select Stream pop u

IPTV Tabs288 FTB-8500 Series and FTB-8120NGE/8130NGEIGMPSelect a stream from the list by pressing on it, or perform a search in the stream list by ent

IPTV TabsEthernet and Fibre Channel Application 289IGMPEnable Auto-Join, available when the test is stopped, enables the IGMP auto-join function. The

IPTV Tabs290 FTB-8500 Series and FTB-8120NGE/8130NGEIGMPSummary (All Multicast Groups)The following gives statistics on all monitored multicast stream

IPTV TabsEthernet and Fibre Channel Application 291IGMPConfiguration IGMP Version: Indicates the supported IGMP version which is IGMP version 2. Note

IPTV Tabs292 FTB-8500 Series and FTB-8120NGE/8130NGEStream InformationStream InformationThe Stream Info tab completes the information provided by the

IPTV TabsEthernet and Fibre Channel Application 293Stream InformationStreamThe Select Stream pop up allows the selection of a stream to see informatio

IPTV Tabs294 FTB-8500 Series and FTB-8120NGE/8130NGEStream InformationDuration Start Time: Indicates the time at which the stream monitoring has star

IPTV TabsEthernet and Fibre Channel Application 295Stream InformationIP Rate (Mbps): Indicates the number of megabits received in the last second (Mb

Physical Interfaces and LEDsEthernet and Fibre Channel Application 17FTB-8525 and FTB-8535 ModelsFTB-8525 and FTB-8535 ModelsFTB-8525 Fibre Channel (1

Ethernet and Fibre Channel Application 29715 RFC 2544 TabsNote: The RFC 2544 tabs are only available with RFC 2544 test.Note: The RFC 2544 measurement

RFC 2544 Tabs298 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal ConfigurationGlobal ConfigurationPress TEST, RFC 2544, and Global.Configuration Frame

RFC 2544 TabsEthernet and Fibre Channel Application 299Global Configuration Frame Size (Bytes): RFC 2544 gives predefined frame size distribution val

RFC 2544 Tabs300 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal ConfigurationTest Procedure Test: Enables the RFC 2544 sub-tests to be performed. Choi

RFC 2544 TabsEthernet and Fibre Channel Application 301Global ConfigurationLatency MeasurementNote: Available with FTB-8120NGE and FTB-8130NGE modules

RFC 2544 Tabs302 FTB-8500 Series and FTB-8120NGE/8130NGEThroughputThroughputThe objective of this test is to find the throughput of the device under t

RFC 2544 TabsEthernet and Fibre Channel Application 303ThroughputConfiguration Test Time (MM:SS): Enter the test time value. Possible values are 1 se

RFC 2544 Tabs304 FTB-8500 Series and FTB-8120NGE/8130NGEThroughput Maximum Rate: TX-to-RX/P1-to-P2/P2-to-P1/Local to Remote/Remote to Local: Select t

RFC 2544 TabsEthernet and Fibre Channel Application 305ThroughputResults Test State--: Indicates that the test has not run yet.In Progress: Indicates

Physical Interfaces and LEDs18 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8525 and FTB-8535 ModelsElectrical 10/100/1000 Mbps EthernetThe FTB-8525/FTB

RFC 2544 Tabs306 FTB-8500 Series and FTB-8120NGE/8130NGEThroughput Throughput Results Frame Size: Indicates the frame sizes used for the test. Up to

RFC 2544 TabsEthernet and Fibre Channel Application 307Back-to-BackBack-to-BackThe objective of this test is to find the maximum number of frames that

RFC 2544 Tabs308 FTB-8500 Series and FTB-8120NGE/8130NGEBack-to-BackConfiguration Max. time worth of frame (MM:SS): Choices are 1 to 5 seconds. The d

RFC 2544 TabsEthernet and Fibre Channel Application 309Back-to-BackResults Test State--: Indicates that the test has not run yet.In Progress: Indicat

RFC 2544 Tabs310 FTB-8500 Series and FTB-8120NGE/8130NGEBack-to-Back Current Trial: Indicates the current trial number. Unit: Select the throughput

RFC 2544 TabsEthernet and Fibre Channel Application 311Frame LossFrame LossThe objective of this test is to find the percentage of frames that are los

RFC 2544 Tabs312 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Loss Test Granularity (%): Select the test granularity. The test granularity is the per

RFC 2544 TabsEthernet and Fibre Channel Application 313Frame LossResults Test State--: Indicates that the test has not run yet.In Progress: Indicates

RFC 2544 Tabs314 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Loss Frame Loss Results Frame Size: Indicates the frame sizes used for the test. Up to

RFC 2544 TabsEthernet and Fibre Channel Application 315LatencyLatencyThe objective of this test is to find the time required for the sent frame to go

Physical Interfaces and LEDsEthernet and Fibre Channel Application 19FTB-8525 and FTB-8535 ModelsOptical Fibre Channel 1x/2x/4x orEthernet 100/1000 Mb

RFC 2544 Tabs316 FTB-8500 Series and FTB-8120NGE/8130NGELatencyConfiguration Test Time (MM:SS): Select the test time value. Choices are 1 second to 2

RFC 2544 TabsEthernet and Fibre Channel Application 317Latency Set All To: Enter a value in the Set All To and press OK to apply the value to all fra

RFC 2544 Tabs318 FTB-8500 Series and FTB-8120NGE/8130NGELatencyResults Test State--: Indicates that the test has not run yet.In Progress: Indicates t

RFC 2544 TabsEthernet and Fibre Channel Application 319Latency Latency ResultsNote: The “--” indicates that the result is not available because the t

RFC 2544 Tabs320 FTB-8500 Series and FTB-8120NGE/8130NGEGraphGraphGives the graph showing the Throughput, Back-to-Back, Frame Loss, or Latency measure

RFC 2544 TabsEthernet and Fibre Channel Application 321Graph Unit: Select the result unit. Choices are: Layer/Displayed Step/ModeLayer (Throughput a

RFC 2544 Tabs322 FTB-8500 Series and FTB-8120NGE/8130NGEGraph Displayed Results: Select the displayed results mode: Current, Minimum, Maximum, or Ave

Ethernet and Fibre Channel Application 32316 EtherSAM TabsNote: The EtherSAM tabs are only available with EtherSAM (Y.1564) test. The EtherSAM tabs ar

EtherSAM Tabs324 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Configuration)Overview (Configuration)The Overview tab allows the activation of up t

EtherSAM TabsEthernet and Fibre Channel Application 325Overview (Configuration)When the Service Performance Test is enabled, up to 10 services can be

Physical Interfaces and LEDs20 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8525 and FTB-8535 Models Carefully connect optical fiber cables to the SFP’

EtherSAM Tabs326 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Configuration)In the third stage of the test, when the Ramp Traffic Policing Rate ch

EtherSAM TabsEthernet and Fibre Channel Application 327Overview (Configuration)Latency MeasurementNote: Available with FTB-8120NGE and FTB-8130NGE mod

EtherSAM Tabs328 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Configuration)Total TX Rate (%)Note: Only available when the Service Performance Tes

EtherSAM TabsEthernet and Fibre Channel Application 329Services (Configuration)Services (Configuration)Press TEST, EtherSAM Configuration, and Service

EtherSAM Tabs330 FTB-8500 Series and FTB-8120NGE/8130NGEServices (Configuration) Framing indicates and allows to change the selected framing. The fra

EtherSAM TabsEthernet and Fibre Channel Application 331Services (Configuration) PBB-TE indicates and allows to change the selected frame PBB-TE desti

EtherSAM Tabs332 FTB-8500 Series and FTB-8120NGE/8130NGEServices (Configuration) CIR+EIR sets the best effort allowed traffic for the service. The EI

EtherSAM TabsEthernet and Fibre Channel Application 333Services (Configuration)Performance Criteria Max Jitter allows to set the maximum jitter value

EtherSAM Tabs334 FTB-8500 Series and FTB-8120NGE/8130NGEServices (Configuration)Test ParametersRamp Traffic Policing Rate allows to stress the rate li

EtherSAM TabsEthernet and Fibre Channel Application 335Ramp (Configuration)Ramp (Configuration)Note: The Ramp tab is only available when the ramp test

Physical Interfaces and LEDsEthernet and Fibre Channel Application 21FTB-8525 and FTB-8535 ModelsFibre Channel 10x and 10G EthernetThe FTB-8525/FTB-85

EtherSAM Tabs336 FTB-8500 Series and FTB-8120NGE/8130NGERamp (Configuration)Step List Step indicates the step number. Up to 10 steps may be configure

EtherSAM TabsEthernet and Fibre Channel Application 337Burst (Configuration)Burst (Configuration)Note: The Burst configuration is only available when

EtherSAM Tabs338 FTB-8500 Series and FTB-8120NGE/8130NGEBurst (Configuration) Burst Frame represents the burst frame ratio in percentage that is equa

EtherSAM TabsEthernet and Fibre Channel Application 339Burst (Configuration)TableNote: Result values are only available for enabled services. Service

EtherSAM Tabs340 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Results)Overview (Results)Press TEST, EtherSAM Results, and Overview.Global Progress

EtherSAM TabsEthernet and Fibre Channel Application 341Overview (Results) Global Verdict indicates the actual test PASS or FAIL verdict. A FAIL ve

EtherSAM Tabs342 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Results) Alarms Link Down: Indicates that the Ethernet connection is down due to a

EtherSAM TabsEthernet and Fibre Channel Application 343Overview (Results) Max Round-Trip Latency (ms) indicates the maximum measured round trip laten

EtherSAM Tabs344 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Results)Service Performance Test OverviewDisplays an overview of the service perform

EtherSAM TabsEthernet and Fibre Channel Application 345Service Configuration Test (Results)Service Configuration Test (Results)Press TEST, EtherSAM Re

Physical Interfaces and LEDs22 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8525 and FTB-8535 ModelsCarefully connect optical fiber cables to the XFP’s

EtherSAM Tabs346 FTB-8500 Series and FTB-8120NGE/8130NGEService Configuration Test (Results)Ramp and Burst Tests Table Step, for ramp test, indicates

EtherSAM TabsEthernet and Fibre Channel Application 347Service Configuration Test (Results) Verdict indicates that the performance metrics (Jitter, L

EtherSAM Tabs348 FTB-8500 Series and FTB-8120NGE/8130NGEService Performance Test (Results)Service Performance Test (Results)Press TEST, EtherSAM Resul

EtherSAM TabsEthernet and Fibre Channel Application 349Service Performance Test (Results)Sequence Tracking Out-Of-Sequence (OOS) is declared when a v

EtherSAM Tabs350 FTB-8500 Series and FTB-8120NGE/8130NGEService Performance Test (Results)Round Trip LatencyThe round trip latency (delay) is measured

Ethernet and Fibre Channel Application 35117 TCP Throughput TabsNote: The TCP Throughput tabs are only available with TCP Throughput test. Not availab

TCP Throughput Tabs352 FTB-8500 Series and FTB-8120NGE/8130NGETCP Throughput ConfigurationPress TEST, TCP Throughput, and TCP Throughput Configuration

TCP Throughput TabsEthernet and Fibre Channel Application 353TCP Throughput Configuration Port: Enter the TCP port number. The default setting is 502

TCP Throughput Tabs354 FTB-8500 Series and FTB-8120NGE/8130NGETCP Throughput ConfigurationTCP Throughput ConfigurationNote: TCP Throughput Configurati

TCP Throughput TabsEthernet and Fibre Channel Application 355TCP Throughput AnalysisTCP Throughput AnalysisNote: Only available on the local unit.Pres

Physical Interfaces and LEDsEthernet and Fibre Channel Application 23FTB-8525 and FTB-8535 Models LEDsLASER LED: The red LASER LED is on when the FTB

TCP Throughput Tabs356 FTB-8500 Series and FTB-8120NGE/8130NGETCP Throughput Analysis Window SizeLast: Indicates the last TCP window size.Minimum: In

Ethernet and Fibre Channel Application 35718 Advanced TabNote: The available Advanced tab depends on which test path is activated.Service Disruption T

Advanced Tab358 FTB-8500 Series and FTB-8120NGE/8130NGEService Disruption Time (SDT)ConfigurationSelect the criteria that will be used for the SDT mea

Advanced TabEthernet and Fibre Channel Application 359Service Disruption Time (SDT) No Defect Time: Available for Defect Mode only. No Defect Time re

Advanced Tab360 FTB-8500 Series and FTB-8120NGE/8130NGEService Disruption Time (SDT) Unit: Select the unit for the statistics. Choices are μs, ms, s,

Ethernet and Fibre Channel Application 36119 Common TabPerformance Monitoring (PM)The Performance Monitoring tab gives error performance events and pa

Common Tab362 FTB-8500 Series and FTB-8120NGE/8130NGEPerformance Monitoring (PM)StandardSelect the desired standard from the list. Choices are:Statist

Common TabEthernet and Fibre Channel Application 363Performance Monitoring (PM) SES (Severely Errored Second)For G.821: Gives the number of seconds w

Common Tab364 FTB-8500 Series and FTB-8120NGE/8130NGEPerformance Monitoring (PM) UAS (Unavailable Second): Gives the count of the seconds correspondi

Ethernet and Fibre Channel Application 36520 System TabsThe System tab gives access to tabs containing general functions related to the FTB-8510B oper

Physical Interfaces and LEDs24 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8120NGE and FTB-8130NGE ModelsFTB-8120NGE and FTB-8130NGE ModelsFTB-8120NGE

System Tabs366 FTB-8500 Series and FTB-8120NGE/8130NGEPreferencesPreferencesPress System, and Preferences/Default Perferences.Time Options Time Forma

System TabsEthernet and Fibre Channel Application 367Preferences Test Time Display Mode: Allows the selection of the test time mode displayed in the

System Tabs368 FTB-8500 Series and FTB-8120NGE/8130NGEDefault/Ethernet Test PreferencesDefault/Ethernet Test PreferencesPress System and Preferences/D

System TabsEthernet and Fibre Channel Application 369Default/Ethernet Test PreferencesNote: The default test preferences are saved per slot on the FTB

System Tabs370 FTB-8500 Series and FTB-8120NGE/8130NGEDefault/Ethernet Test PreferencesInterface ConfigurationNote: The following IPv4 configuration p

System TabsEthernet and Fibre Channel Application 371IPv6 Test PreferencesIPv6 Test PreferencesPress System and Preferences/IPv6 Test Preferences.Note

System Tabs372 FTB-8500 Series and FTB-8120NGE/8130NGEIPv6 Test Preferences Global IPv6 Address: The Global IPv6 Address (GUA) is used to communicate

System TabsEthernet and Fibre Channel Application 373IPv6 Test Preferences Default Gateway Address: The Default Gateway Address is used to forward pa

System Tabs374 FTB-8500 Series and FTB-8120NGE/8130NGEFC Test PreferencesFC Test PreferencesNote: Not available with FTB-8510G.Press System and Prefer

System TabsEthernet and Fibre Channel Application 375FC Test PreferencesConfigurationLaser On: Allows to select Laser On every time a test is created

Physical Interfaces and LEDsEthernet and Fibre Channel Application 25FTB-8120NGE and FTB-8130NGE ModelsThe following table shows the list of available

System Tabs376 FTB-8500 Series and FTB-8120NGE/8130NGEModule InformationModule InformationPress System and Module Information. Installed Software Pac

System TabsEthernet and Fibre Channel Application 377Module Information Hardware OptionsGives hardware information related to the SFP/XFP.SFP/XFP: Th

System Tabs378 FTB-8500 Series and FTB-8120NGE/8130NGESoftware OptionsSoftware OptionsAllows the installation of software options. A software option k

System TabsEthernet and Fibre Channel Application 379Software OptionsAvailable OptionsThe available software options are listed with the Status indica

System Tabs380 FTB-8500 Series and FTB-8120NGE/8130NGESoftware OptionsFeature SK-802-3AH The 802.3ah OAM Protocol is enabled.SK-TCP-THPUT The TCP Thro

System TabsEthernet and Fibre Channel Application 381Software OptionsFor FTB-8120NGE/FTB-8130NGE and FTB-8525/FTB-8535Category Name DescriptionInterfa

System Tabs382 FTB-8500 Series and FTB-8120NGE/8130NGESoftware OptionsFor FTB-8510GCategory Name DescriptionInterface SK-ADV-FILTERS Advanced Traffic

System TabsEthernet and Fibre Channel Application 383Clock SynchronizationClock SynchronizationNote: Clock Synchronization is only available for Ether

System Tabs384 FTB-8500 Series and FTB-8120NGE/8130NGEClock Synchronization Line Coding: Allows the selection of the interface line coding. Choices a

System TabsEthernet and Fibre Channel Application 385Clock Synchronization Frequency: The Frequency alarm indicates if the received signal rate meets

iv FTB-8500 Series and FTB-8120NGE/8130NGE6 Creating and Starting a Test Case ...65Introduc

Physical Interfaces and LEDs26 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8120NGE and FTB-8130NGE Models LEDsLED Status DescriptionLINK/ACT(Green)On

System Tabs386 FTB-8500 Series and FTB-8120NGE/8130NGEClock SynchronizationBackplaneThe backplane feature allows sharing the same backplane 8 kHz cloc

System TabsEthernet and Fibre Channel Application 387Clock SynchronizationRef OutputNote: Ref Output is only available with FTB-8510G, FTB-8535, and F

System Tabs388 FTB-8500 Series and FTB-8120NGE/8130NGERemote ControlRemote ControlPress System, and Remote Control.User InformationThe User Informatio

Ethernet and Fibre Channel Application 38921 Tools TabsNote: The To ols tabs are only available when a test is created.TabAvailable withPageEthernet F

Tools Tabs390 FTB-8500 Series and FTB-8120NGE/8130NGEScriptScriptThe scripting tool allows a user to automate test process by creating scripts contain

Tools TabsEthernet and Fibre Channel Application 391ScriptEditLists the content of the current script and allows its edition. Users with writing knowl

Tools Tabs392 FTB-8500 Series and FTB-8120NGE/8130NGEScriptScript ToolsAllows automatic generation of scripts by setting step by step the parameters f

Tools TabsEthernet and Fibre Channel Application 393ScriptNote: However, for RFC 2544, all selected tests (Throughput, Back-to-Back, Frame Loss, and/o

Tools Tabs394 FTB-8500 Series and FTB-8120NGE/8130NGEPing ConfigurationPing ConfigurationThe Ping tool is used to determine if a network device is rea

Tools TabsEthernet and Fibre Channel Application 395Ping Configuration Delay (ms): Available for ping only. Enter the delay between each attempt (PIN

Physical Interfaces and LEDsEthernet and Fibre Channel Application 27FTB-8120NGE and FTB-8130NGE ModelsOptical 100/1000 Mbps Ethernet or1x/2x/4x Fibre

Tools Tabs396 FTB-8500 Series and FTB-8120NGE/8130NGEPing ResultsPing ResultsPress Tools, Ping, in the Tool list, press Ping, and press Result.Note: F

Tools TabsEthernet and Fibre Channel Application 397Ping ResultsTime Out When an ICMPv4/ICMPv6 echo reply was not received within the defined timeout.

Tools Tabs398 FTB-8500 Series and FTB-8120NGE/8130NGEPing ResultsFor IPv4: Replied From: Indicates the IP address of the replier. Bytes: Indicates t

Tools TabsEthernet and Fibre Channel Application 399Trace Route ConfigurationTrace Route ConfigurationTrace Route is used to obtain the list of all ro

Tools Tabs400 FTB-8500 Series and FTB-8120NGE/8130NGETrace Route ResultsTrace Route ResultsPress Tools, Ping, Configuration, in the Tool list, press T

Tools TabsEthernet and Fibre Channel Application 401Trace Route Results Status: Indicates the status of the attempt.Status DescriptionSuccessful Vali

Tools Tabs402 FTB-8500 Series and FTB-8120NGE/8130NGETrace Route Results Replied From: Indicates the IP address of the replier. Time (ms): Indicates

Tools TabsEthernet and Fibre Channel Application 403ENIU ConfigurationENIU ConfigurationAllows supporting the Operation, Administration, and Maintenan

Tools Tabs404 FTB-8500 Series and FTB-8120NGE/8130NGEADC ConfigurationADC ConfigurationNote: The ADC Config tab is only available when ADC is selected

Tools TabsEthernet and Fibre Channel Application 405ADC Configuration ENIU Status: Indicates the ENIU status. Possible statuses are:Valid: The remote

Physical Interfaces and LEDs28 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8120NGE and FTB-8130NGE Models Carefully connect optical fiber cables to th

Tools Tabs406 FTB-8500 Series and FTB-8120NGE/8130NGEADC ConfigurationSelected ENIUIndicates the information related to the selected ENIU. MAC Addres

Tools TabsEthernet and Fibre Channel Application 407ADC ConfigurationLoopbackAllows sending a loopback request to the selected ENIU.Note: If the selec

Tools Tabs408 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Configuration802.3ah ConfigurationNote: The 802.3ah Config tab is only available when 802

Tools TabsEthernet and Fibre Channel Application 409802.3ah Configuration LoopbackRequest allows the selection of the loopback request to be sent to

Tools Tabs410 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Statistics802.3ah StatisticsNote: The 802.3ah Stats tab is only available when 802.3ah is

Tools TabsEthernet and Fibre Channel Application 411802.3ah Statistics Parser Action: Bits 0 and 1 of the State byte report the Parser Action.Forward

Tools Tabs412 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Statistics OUI: The 24-bit IEEE Organizationally Unique Identifer field identifies the v

Tools TabsEthernet and Fibre Channel Application 413802.3ah Events802.3ah EventsNote: The 802.3ah Events tab is only available when 802.3ah is selecte

Tools Tabs414 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Events Threshold. Error Count. Error Running Total. Event Running TotalSymbol Period

Tools TabsEthernet and Fibre Channel Application 415Traffic ScanTraffic ScanThe traffic scan tool provides the capability to discover and monitor VLAN

Physical Interfaces and LEDsEthernet and Fibre Channel Application 29FTB-8120NGE and FTB-8130NGE Models10G Ethernet and Fibre Channel 10xThe FTB-8525/

Tools Tabs416 FTB-8500 Series and FTB-8120NGE/8130NGETraffic ScanLevelAllows the selection of the criteria that will be used to filter the incoming VL

Tools TabsEthernet and Fibre Channel Application 417Traffic ScanLink Rate (Mbps)Indicates the network link rate based on the received frames with a va

Tools Tabs418 FTB-8500 Series and FTB-8120NGE/8130NGETraffic ScanMonitored Frames TableStatistics are gathered for each different traffic flow matchin

Tools TabsEthernet and Fibre Channel Application 419Traffic ScanFor MPLS Mode, the level of MPLS (Unlabeled, 1 Label, 2 Labels), and the values of Lab

Tools Tabs420 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Scan FiltersThe column’s All/Ignore toggle buttons are used to set the filtering criteri

Tools TabsEthernet and Fibre Channel Application 421Traffic Scan Frame Count indicates for each traffic flow, the number of frames matching the selec

Ethernet and Fibre Channel Application 42322 Expert Mode TabsNote: The Expert Mode tabs are only available with BERT and RFC 2544 Ethernet tests (not

Expert Mode Tabs424 FTB-8500 Series and FTB-8120NGE/8130NGEExpert Mode (RFC 2544)Expert Mode (RFC 2544)Expert Mode allows the configuration of the thr

Expert Mode TabsEthernet and Fibre Channel Application 425Expert Mode (RFC 2544)Expert Mode StatusGives the verdict, Pass or Fail, of the Throughput,

Physical Interfaces and LEDs30 FTB-8500 Series and FTB-8120NGE/8130NGEFTB-8120NGE and FTB-8130NGE ModelsCarefully connect optical fiber cables to the

Expert Mode Tabs426 FTB-8500 Series and FTB-8120NGE/8130NGEThroughput (RFC 2544)Throughput (RFC 2544)Press TEST, Expert Mode, and Throughput. Enable

Expert Mode TabsEthernet and Fibre Channel Application 427Throughput (RFC 2544) Unit: Select the unit. Choices are: bps, Kbps, Mbps, Bps, KBps, MBps,

Expert Mode Tabs428 FTB-8500 Series and FTB-8120NGE/8130NGEBack-to-Back (RFC 2544)Back-to-Back (RFC 2544)Press TEST, Expert Mode, and Back-to-Back. E

Expert Mode TabsEthernet and Fibre Channel Application 429Back-to-Back (RFC 2544) Unit: Select the unit. Choices are: bps, Kbps, Mbps, Bps, KBps, MBp

Expert Mode Tabs430 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Loss (RFC 2544)Frame Loss (RFC 2544)Press TEST, Expert Mode, and Frame Loss. Enable

Expert Mode TabsEthernet and Fibre Channel Application 431Frame Loss (RFC 2544) Displayed Step: Indicates the last percentage of the speed used for t

Expert Mode Tabs432 FTB-8500 Series and FTB-8120NGE/8130NGELatency (RFC 2544)Latency (RFC 2544)Press TEST, Expert Mode, and Latency. Enable Criteria:

Expert Mode TabsEthernet and Fibre Channel Application 433Latency (RFC 2544) Unit: Select the unit. Choices are s, ms, μs, and ns. The default settin

Expert Mode Tabs434 FTB-8500 Series and FTB-8120NGE/8130NGEExpert Mode (BERT)Expert Mode (BERT)Expert Mode allows the configuration of the thresholds

Expert Mode TabsEthernet and Fibre Channel Application 435Port (BERT)Port (BERT)Press TEST, Expert Mode, and Port.Enable Criteria: Enable Criteria ena

Physical Interfaces and LEDsEthernet and Fibre Channel Application 31FTB-8120NGE and FTB-8130NGE Models LEDsLASER LED: The red LASER LED is on when t

Expert Mode Tabs436 FTB-8500 Series and FTB-8120NGE/8130NGEPort (BERT)FrequencyEnter the minimum and maximum frequency offsets either in ppm or bps ac

Expert Mode TabsEthernet and Fibre Channel Application 437Ethernet (BERT)Ethernet (BERT)Press TEST, Expert Mode, and Ethernet.Enable Criteria: Enable

Expert Mode Tabs438 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet (BERT)ErrorsEnter the threshold value for each error. Status: Indicates the real-

Expert Mode TabsEthernet and Fibre Channel Application 439Pattern (BERT)Pattern (BERT)Press TEST, Expert Mode, and Pattern.Enable Criteria: Enable Cri

Expert Mode Tabs440 FTB-8500 Series and FTB-8120NGE/8130NGEPattern (BERT)ErrorsEnter the threshold value for Bit Error. Status: Indicates the real-ti

Ethernet and Fibre Channel Application 44123 Automatic Power Failure RecoveryThe automatic power failure recovery is used to re-create and restart the

Automatic Power Failure Recovery442 FTB-8500 Series and FTB-8120NGE/8130NGEManual Power Failure RecoveryIf only the requirement number 1 is met, the s

Ethernet and Fibre Channel Application 44324 MaintenanceTo help ensure long, trouble-free operation: Always inspect fiber-optic connectors before usi

Maintenance444 FTB-8500 Series and FTB-8120NGE/8130NGERecalibrating the UnitRecalibrating the UnitManufacturing and service center calibrations are ba

Ethernet and Fibre Channel Application 44525 TroubleshootingSolving Common ProblemsBefore calling EXFO’s technical support, please read the following

Troubleshooting446 FTB-8500 Series and FTB-8120NGE/8130NGEContacting the Technical Support GroupContacting the Technical Support Group To accelerate t

Ethernet and Fibre Channel Application 44726 WarrantyGeneral InformationEXFO Inc. (EXFO) warrants this equipment against defects in material and workm

Warranty448 FTB-8500 Series and FTB-8120NGE/8130NGELiabilityLiabilityEXFO shall not be liable for damages resulting from the use of the product, nor s

WarrantyEthernet and Fibre Channel Application 449ExclusionsExclusionsEXFO reserves the right to make changes in the design or construction of any of

Warranty450 FTB-8500 Series and FTB-8120NGE/8130NGEService and RepairsService and RepairsEXFO commits to providing product service and repair for five

WarrantyEthernet and Fibre Channel Application 451EXFO Service Centers WorldwideEXFO Service Centers WorldwideIf your product requires servicing, cont

Ethernet and Fibre Channel Application 453ASpecificationsEthernet Optical InterfacesFor FTB-8510B:IMPORTANTThe following technical specifications can

Specifications454 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Optical InterfacesFor FTB-8510G:Jitter compliance IEEE 802.3ah IEEE 802.3ahEthernet

SpecificationsEthernet and Fibre Channel Application 455Ethernet Optical InterfacesFor FTB-8120NGE/FTB-8130NGE and FTB-8525/FTB-8535:100 Mbit/s AND Gi

Ethernet and Fibre Channel Application 335 Introducing the Smart User InterfaceStarting the Module ApplicationTo Start the FTB-8500 Series and FTB-812

Specifications456 FTB-8500 Series and FTB-8120NGE/8130NGEFibre Channel InterfacesFibre Channel InterfacesFor FTB-8510B:FC-1X/2XWavelength (nm) 850 131

SpecificationsEthernet and Fibre Channel Application 457Fibre Channel InterfacesFor FTB-8120NGE/FTB-8130NGE and FTB-8525/FTB-8535:Wavelength (nm) 850

Specifications458 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Electrical InterfacesEthernet Electrical InterfacesFor FTB-8510B:For FTB-8120NGE/FTB

SpecificationsEthernet and Fibre Channel Application 459Ethernet Electrical InterfacesEthernet CablesMinimum Category 3 cable is required for 10Base-T

Specifications460 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Electrical Interfaces Straight Through Cable (1000 Mbps) Crossover Cable (1000 Mbp

SpecificationsEthernet and Fibre Channel Application 461Synchronization InterfacesSynchronization InterfacesFor FTB-8510G:For FTB-8120NGE/FTB-8130NGE

Ethernet and Fibre Channel Application 463B GlossaryAcronym ListAB?HelpAC Alternating CurrentACT ActivityAIS Alarm Indication SignalAIS-L Alarm Indi

Glossary464 FTB-8500 Series and FTB-8120NGE/8130NGEAcronym ListCBB_Credit Buffer-to-Buffer CreditBBE Background Block ErrorBBER Background Block Error

GlossaryEthernet and Fibre Channel Application 465Acronym ListDCRC Cyclic Redundancy CheckCRC-7 Cyclic Redundancy Check on 7 bitsCRITIC CriticalCRITIC

Introducing the Smart User Interface34 FTB-8500 Series and FTB-8120NGE/8130NGEStarting the Module Application4. For FTB-8120NGE/FTB-8130NGE only, on t

Glossary466 FTB-8500 Series and FTB-8120NGE/8130NGEAcronym ListEE-VLAN Extended - Virtual Local Area NetworkE1 European standard for digital transmiss

GlossaryEthernet and Fibre Channel Application 467Acronym ListFGHEXP ExperimentalEXT CLK External ClockF_CTL Frame ControlFC Fibre ChannelFCC Federal

Glossary468 FTB-8500 Series and FTB-8120NGE/8130NGEAcronym ListIHTML Hyper Text Markup LanguageHz HertzI-TAG Backbone Service Instance TagIC Industry

GlossaryEthernet and Fibre Channel Application 469Acronym ListKLKbps KiloBit Per SecondKBps KiloByte Per SecondKg KilogramL3 Layer 3L4 Layer 4LAN Loca

Glossary470 FTB-8500 Series and FTB-8120NGE/8130NGEAcronym ListMNLSR Label Switching RouterLSS Loss of Sequence SynchronizationmMinutem MeterMAC Media

GlossaryEthernet and Fibre Channel Application 471Acronym ListOPNE Network Elementnm Nanometerns NanosecondOAM Operation Administration ManagementOH O

Glossary472 FTB-8500 Series and FTB-8120NGE/8130NGEAcronym ListQRPHY Physical Layer DevicePID Packet IdentifierPLM-P Payload Label Mismatch - PathPM P

GlossaryEthernet and Fibre Channel Application 473Acronym ListSRFC Request For CommentsRMA Return Merchandise AuthorizationRS Regenerator SectionRX Re

Glossary474 FTB-8500 Series and FTB-8120NGE/8130NGEAcronym ListTSMASub-Miniature A ConnectorSMF Single Mode FiberSNAP Sub Network Access PointSOF Star

GlossaryEthernet and Fibre Channel Application 475Acronym ListUVWXUAS Unavailable SecondUDP User Data ProtocolUNEQ-P Unequipped - PathμsmicrosecondUSA

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 35Main WindowMain WindowApplication nameMinimizeHelpExitTab sTab (s )Tab ’

Glossary476 FTB-8500 Series and FTB-8120NGE/8130NGEVLAN/B-VLANVLAN/B-VLANSpecial VID/B-VID values (IEEE Std 802.1Q-1998)VLAN/B-VLAN PriorityID Descri

GlossaryEthernet and Fibre Channel Application 477MPLS LabelsMPLS LabelsThe MPLS labels are listed in the following table.Label Description0 IPv4 expl

Glossary478 FTB-8500 Series and FTB-8120NGE/8130NGEPath Signal Label (C2 byte)Path Signal Label (C2 byte)Indicates the content of the STS SPE, includi

Ethernet and Fibre Channel Application 479C Pop-Up WindowsNote: The following Pop-Up windows are available throughout the user interface.Tab PageVLAN

Pop-Up Windows480 FTB-8500 Series and FTB-8120NGE/8130NGEVLAN ConfigurationVLAN Configuration Enable VLAN appears only for EtherSAM service configura

Pop-Up WindowsEthernet and Fibre Channel Application 481PBB-TE Interface configurationPBB-TE Interface configurationThe PBB-TE Interface window allows

Pop-Up Windows482 FTB-8500 Series and FTB-8120NGE/8130NGEPBB-TE Interface configuration B-VLAN (Backbone Virtual Local Area Network)ID: Enter the B-V

Pop-Up WindowsEthernet and Fibre Channel Application 483IPv4 ConfigurationIPv4 ConfigurationSourceNote: For EtherSAM Dual Test Set, the source IP addr

Pop-Up Windows484 FTB-8500 Series and FTB-8120NGE/8130NGEIPv4 Configuration Resolve MAC Address: When enabled, will send a request to the network to

Pop-Up WindowsEthernet and Fibre Channel Application 485IPv6 Address ConfigurationIPv6 Address ConfigurationNote: The default IPv6 address parameters

Ethernet and Fibre Channel Application v9 Traffic Analyzer Tabs ... 159E

Introducing the Smart User Interface36 FTB-8500 Series and FTB-8120NGE/8130NGEMain WindowTabsThe SUI application contains the following four main appl

Pop-Up Windows486 FTB-8500 Series and FTB-8120NGE/8130NGEIPv6 Address ConfigurationGlobal IPv6 AddressThe Global IPv6 Address (GUA) is used for global

Pop-Up WindowsEthernet and Fibre Channel Application 487IPv6 Address Configuration Link-Local/Global IPv6 Address StatusMode Status DescriptionStatel

Pop-Up Windows488 FTB-8500 Series and FTB-8120NGE/8130NGEIPv6 Address ConfigurationDefault Gateway AddressThe Default Gateway Address is used to forwa

Pop-Up WindowsEthernet and Fibre Channel Application 489IPv6 Address ConfigurationDestination IPv6 AddressNote: Destination IPv6 address is only avail

Pop-Up Windows490 FTB-8500 Series and FTB-8120NGE/8130NGECopy Service Network ConfigurationCopy Service Network ConfigurationThis pop-up window is onl

Pop-Up WindowsEthernet and Fibre Channel Application 491Service Profile ConfigurationService Profile ConfigurationThis pop-up window is only available

Pop-Up Windows492 FTB-8500 Series and FTB-8120NGE/8130NGEFraming ConfigurationFraming ConfigurationThis pop-up window is only available with EtherSAM

Pop-Up WindowsEthernet and Fibre Channel Application 493Frame Size ConfigurationFrame Size ConfigurationThis pop-up window is only available with Ethe

Pop-Up Windows494 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Size ConfigurationThe following table lists each component that may affect the minimum

Pop-Up WindowsEthernet and Fibre Channel Application 495Frame Format ConfigurationFrame Format ConfigurationThis pop-up window is only available with

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 37Main WindowFor Dual ports (FTB-8510B only), see the figure below for the

Pop-Up Windows496 FTB-8500 Series and FTB-8120NGE/8130NGEMAC ConfigurationMAC ConfigurationThis pop-up window is only available with EtherSAM (Y.1564)

Pop-Up WindowsEthernet and Fibre Channel Application 497MPLS ConfigurationMPLS ConfigurationThis pop-up window is only available with EtherSAM (Y.1564

Pop-Up Windows498 FTB-8500 Series and FTB-8120NGE/8130NGEMPLS Configuration COS/EXP (Class Of Service / Experimental): Select the class of service. T

Pop-Up WindowsEthernet and Fibre Channel Application 499UDP ConfigurationUDP ConfigurationThis pop-up window is only available with EtherSAM (Y.1564)

Pop-Up Windows500 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced TOS/DSAdvanced TOS/DSEnable Differentiated ServicesAllows enabling the Differentiate

Pop-Up WindowsEthernet and Fibre Channel Application 501Advanced TOS/DSTOSNote: TOS is available when Enable Differentiated Services is not enabled.

Pop-Up Windows502 FTB-8500 Series and FTB-8120NGE/8130NGEPingPingThe Ping is used to determine if a network device is reachable.Note: The Ping button

Pop-Up WindowsEthernet and Fibre Channel Application 503Ping Delay (ms): Available for ping only. Enter the delay between each attempt (PING). Choice

Pop-Up Windows504 FTB-8500 Series and FTB-8120NGE/8130NGEFilter SelectionFilter SelectionThis pop-up window is only available from Traffic Analyzer -

Pop-Up WindowsEthernet and Fibre Channel Application 505Truncation CalculatorTruncation CalculatorThis pop-up window is only available from Traffic An

Introducing the Smart User Interface38 FTB-8500 Series and FTB-8120NGE/8130NGEMain WindowIn this user guide, the tabs are grouped as shown below:  Su

Pop-Up Windows506 FTB-8500 Series and FTB-8120NGE/8130NGEField Match ConfigurationField Match ConfigurationThis pop-up window is only available from T

Pop-Up WindowsEthernet and Fibre Channel Application 507Field Match ConfigurationMask: Allows masking the defined filter value. A bit mask of 1 indica

Pop-Up Windows508 FTB-8500 Series and FTB-8120NGE/8130NGETriggered Frame DetailsTriggered Frame DetailsThis pop-up window is only available from Traff

Pop-Up WindowsEthernet and Fibre Channel Application 509Data Capture ExportData Capture ExportThis pop-up window is only available from Traffic Analyz

Pop-Up Windows510 FTB-8500 Series and FTB-8120NGE/8130NGEData Capture ExportOnce generated, the capture file will be automatically opened in Wireshark

IndexEthernet and Fibre Channel Application 511Index-- statusExpert Mode ... 120RFC 2544 ...

Index512 FTB-8500 Series and FTB-8120NGE/8130NGEAutomatic IP Address . 75, 76, 82, 91, 98, 105, 112, 150, 483Auto-Negotiation ...

IndexEthernet and Fibre Channel Application 513CC ... 52, 360C2 ...

Index514 FTB-8500 Series and FTB-8120NGE/8130NGEdate... 45, 130Default ...

IndexEthernet and Fibre Channel Application 515enable port criteria... 435enable sync ...

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 39Main WindowApplication TitleDisplays the software application title which

Index516 FTB-8500 Series and FTB-8120NGE/8130NGEReset to Default button ... 235RX_ID...

IndexEthernet and Fibre Channel Application 517HH ... 42, 52, 360H. Reset...

Index518 FTB-8500 Series and FTB-8120NGE/8130NGEKK1 ... 249K2 ...

IndexEthernet and Fibre Channel Application 519MM1 ... 249MAC ...

Index520 FTB-8500 Series and FTB-8120NGE/8130NGEno ... 200, 203no defect time...

IndexEthernet and Fibre Channel Application 521PBB-TE RX Throughput ... 169Bandwidth ...

Index522 FTB-8500 Series and FTB-8120NGE/8130NGErelative ... 367reliability ...

IndexEthernet and Fibre Channel Application 523service centers... 451Service Configuration Test... 72, 83, 32

Index524 FTB-8500 Series and FTB-8120NGE/8130NGEStream Name200, 203, 266, 269, 271, 274, 293Stream No. 207, 216, 218, 221, 223, 226, 239Stream Tag in

IndexEthernet and Fibre Channel Application 525Software Options... 378Stream Analyzer Overview ... 237st

Introducing the Smart User Interface40 FTB-8500 Series and FTB-8120NGE/8130NGEMain WindowHelpThe help button ( ? ) displays the help information on th

Index526 FTB-8500 Series and FTB-8120NGE/8130NGETools tabs... 389top page ...

IndexEthernet and Fibre Channel Application 527VC-1 ... 284, 293Verdict ...

NOTICE抩⛙CHINESE REGULATION ON RESTRICTION OF HAZARDOUS SUBSTANCES₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩NAMES AND CONTENTS OF THE TOXIC OR HAZARDOUS SUBSTANCES OR ELEMENTS CONT

MARKING REQUIREMENTS㪖㽷尐㻑Productℶ❐Environmental protection use period (years)䘾⬒≬㔳∎䞷㦮棟 ( ㄃ )Logo㪖㉦This Exfo product㦻 EXFO ℶ❐10Batterya䟄㻯aa. If applicabl

www.EXFO.com · [email protected]/N: 1062432CORPORATE HEADQUARTERS 400 Godin Avenue Quebec (Quebec) G1M 2K2 CANADATel.: 1 418 683-0211 · Fax: 1 418 683-

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 41Main WindowExit For FTB-8510B, FTB-8510G, FTB-8525, and FTB-8535:The exi

Introducing the Smart User Interface42 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal Test Status and ControlsGlobal Test Status and ControlsGlobal Tes

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 43Global Test Status and Controls Current status: Indicates the current al

Introducing the Smart User Interface44 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal Test Status and ControlsLoadb: Loads a previously saved configura

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 45Global Test Status and ControlsRemote StatusIndicates whether the remote

vi FTB-8500 Series and FTB-8120NGE/8130NGE14 IPTV Tabs ...

Introducing the Smart User Interface46 FTB-8500 Series and FTB-8120NGE/8130NGEFavoritesFavoritesFavorites gives access to 10 factory test case configu

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 47FavoritesOverwrite Selected Favorite ContentThe factory test case configu

Introducing the Smart User Interface48 FTB-8500 Series and FTB-8120NGE/8130NGETest Report GenerationTest Report GenerationPress Report from the Global

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 49Test Report Generation Report Settings: These parameters are used to ide

Introducing the Smart User Interface50 FTB-8500 Series and FTB-8120NGE/8130NGETest Report Generation Generate button: Allows generating and saving th

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 51Test Report GenerationSections Tab Pre-defined selection: Allows selecti

Introducing the Smart User Interface52 FTB-8500 Series and FTB-8120NGE/8130NGETypical Tab ElementsTypical Tab ElementsOnce the test is created, differ

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 53Typical Tab ElementsAlarm/Error MeasurementsNote: Alarms/Errors are only

Introducing the Smart User Interface54 FTB-8500 Series and FTB-8120NGE/8130NGETypical Tab ElementsTable SortingTables offer sorting capabilities on on

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 55Tab ConfigurationTab ConfigurationOnce the test is created, other tabs ne

Ethernet and Fibre Channel Application vii21 Tools Tabs ...

Introducing the Smart User Interface56 FTB-8500 Series and FTB-8120NGE/8130NGETab ConfigurationThis tab configuration window allows configuration of a

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 57Tab ConfigurationDefined TabsAllows the selection of a tab.Up and down ar

Introducing the Smart User Interface58 FTB-8500 Series and FTB-8120NGE/8130NGETab ConfigurationHelp Button (?)Displays the help information related to

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 59Keyboard UsageKeyboard UsageThe SUI pops up different keyboards to modify

Introducing the Smart User Interface60 FTB-8500 Series and FTB-8120NGE/8130NGEKeyboard Usage Numerical keyboards: Allows entering integer/decimal val

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 61Keyboard Usage Time Keyboard: Allows entering a time value. Date keyboa

Introducing the Smart User Interface62 FTB-8500 Series and FTB-8120NGE/8130NGEKeyboard Usage Hexadecimal keyboards: Allows entering hexadecimal value

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 63Keyboard Usage Full keyboard: Allows entering numbers, letters and some

Introducing the Smart User Interface64 FTB-8500 Series and FTB-8120NGE/8130NGEKeyboard UsageITU T.50 Charactersb7 to b1 Character Description b7 to b1

Ethernet and Fibre Channel Application 656 Creating and Starting a Test CaseA test case can be created using one of the following methods: Test Setup

viii FTB-8500 Series and FTB-8120NGE/8130NGEA Specifications ...

Creating and Starting a Test Case66 FTB-8500 Series and FTB-8120NGE/8130NGEIntroducing the Test SetupIntroducing the Test SetupThe Test Setup window i

Creating and Starting a Test CaseEthernet and Fibre Channel Application 67Introducing the Test Setup Test Setup Controls: Back returns to the previo

Creating and Starting a Test Case68 FTB-8500 Series and FTB-8120NGE/8130NGEIntroducing the Test SetupThe test path is created through the configuratio

Creating and Starting a Test CaseEthernet and Fibre Channel Application 69Introducing the Test SetupStepsAvailable withThe Test step is the root of th

Creating and Starting a Test Case70 FTB-8500 Series and FTB-8120NGE/8130NGETest Case Avail abilityTest Case AvailabilityThe remaining of this chapter

Creating and Starting a Test CaseEthernet and Fibre Channel Application 71EtherSAM (Y.1564) Test CaseEtherSAM (Y.1564) Test CaseITU-T Y.1564 is the ne

Creating and Starting a Test Case72 FTB-8500 Series and FTB-8120NGE/8130NGEEtherSAM (Y.1564) Test CaseTo create an EtherSAM (Y.1564) test case:1. Test

Creating and Starting a Test CaseEthernet and Fibre Channel Application 73EtherSAM (Y.1564) Test Case2. Port configuration:2a. Select the port Connect

Creating and Starting a Test Case74 FTB-8500 Series and FTB-8120NGE/8130NGEEtherSAM (Y.1564) Test Case3. Optical configuration for Ethernet 10G interf

Creating and Starting a Test CaseEthernet and Fibre Channel Application 75EtherSAM (Y.1564) Test Case4c. Select the Frame Format. Choices are Ethernet

Certification InformationEthernet and Fibre Channel Application ixCertification InformationFederal Communications Commission (FCC) and Industry Canada

Creating and Starting a Test Case76 FTB-8500 Series and FTB-8120NGE/8130NGEEtherSAM (Y.1564) Test Case4g. For IPv6, press the IPv6 Config button to se

Creating and Starting a Test CaseEthernet and Fibre Channel Application 77EtherSAM (Y.1564) Test Case6. Services must be enabled before starting the t

Creating and Starting a Test Case78 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test CasesEthernet Et

Creating and Starting a Test CaseEthernet and Fibre Channel Application 79Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test CasesTo create an

Creating and Starting a Test Case80 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases2. Port con

Creating and Starting a Test CaseEthernet and Fibre Channel Application 81Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases3. Optical c

Creating and Starting a Test Case82 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases4. Framing

Creating and Starting a Test CaseEthernet and Fibre Channel Application 83Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test CasesCreate the t

Creating and Starting a Test Case84 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases1c. From th

Creating and Starting a Test CaseEthernet and Fibre Channel Application 85Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases1e. Press Sc